Connecting the device was accomplished with a slightly modified set of procedures from the original example found on AdaFruit. Most notably the use of 3.3V vs 5V to support the different levels on the Arduino Zero. Note that a 10K pull-up resistor is also used on pin 2.
After compiling and downloading the sketch below, the temperature/humidity was successfully obtained and published/visible on the network via Chrome.
The source code used to implement the WiFi Weather Web Server is seen below.
#include <SPI.h>
#include <WiFi101.h>
#include "DHT.h"
char ssid[] = "mynetwork"; // your network SSID (name)
char pass[] = "mypassword"; // your network password
int status = WL_IDLE_STATUS; // the Wifi radio's status
WiFiServer server(80);
#define DHTPIN 2 // what digital pin we're connected to
#define DHTTYPE DHT22 // DHT 22 (AM2302), AM2321, RHT03
DHT dht(DHTPIN, DHTTYPE); // Initialize DHT sensor.
void setup()
{
// initialize serial:
Serial.begin(9600);
while (!Serial)
{
; // wait for serial port to connect. Needed for native USB port only
}
dht.begin();
if (WiFi.status() == WL_NO_SHIELD)
{
Serial.println("WiFi shield not present");
// don't continue:
while (true);
}
// attempt to connect to Wifi network:
while ( status != WL_CONNECTED)
{
// attempt to connect using WPA2 encryption:
Serial.println("");
Serial.println("Attempting to connect to WPA2 network...");
status = WiFi.begin(ssid, pass);
if (status != WL_CONNECTED)
{
// if you're not connected, stop here:
Serial.println("Network unavailable, trying again in 10 seconds...");
// wait 10 seconds for connection:
delay(10000);
}
}
server.begin();
Serial.println("Connected to network");
printWifiStatus();
}
void loop()
{
// listen for incoming clients
WiFiClient client = server.available();
if (client)
{
Serial.println("new client...");
// Wait a few seconds between measurements.
delay(2000);
// Reading temperature or humidity takes about 250 milliseconds!
// Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
float h = dht.readHumidity();
// Read temperature as Celsius (the default)
float t = dht.readTemperature();
// Read temperature as Fahrenheit (isFahrenheit = true)
float f = dht.readTemperature(true);
// Check if any reads failed and exit early (to try again).
if (isnan(h) || isnan(t) || isnan(f)) {
Serial.println("Failed to read from DHT sensor!");
f = 0;
h = 0;
t = 0;
}
// Compute heat index in Fahrenheit (the default)
float hif = dht.computeHeatIndex(f, h);
// Compute heat index in Celsius (isFahreheit = false)
float hic = dht.computeHeatIndex(t, h, false);
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected())
{
if (client.available())
{
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank)
{
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion of the response
//client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("<!DOCTYPE HTML>");
client.println("<html>");
client.println("<head><title>Arduino Web Server</title></head>");
client.println("<body>");
client.print("Humidity is ");
client.print(h);
client.println("<br />");
client.print("Temperature is ");
client.print(t);
client.println(" (C) <br />");
client.print("Temperature is ");
client.print(f);
client.println(" (F) <br />");
client.print("Heat Index is ");
client.print(hic);
client.println(" (C) <br />");
client.print("Heat Index is ");
client.print(hif);
client.println(" (F) <br />");
client.println("</body>");
client.println("</html>");
break;
}
if (c == '\n')
{
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r')
{
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected...");
}
}
void printWifiStatus()
{
// print the SSID of the network you're attached to:
Serial.print("SSID: ");
Serial.println(WiFi.SSID());
// print your WiFi shield's IP address:
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);
// print your gateway address:
IPAddress gateway = WiFi.gatewayIP();
Serial.print("Gateway: ");
Serial.println(gateway);
// print the received signal strength:
long rssi = WiFi.RSSI();
Serial.print("signal strength (RSSI):");
Serial.print(rssi);
Serial.println(" dBm");
}
